oil level TOYOTA CAMRY 1994 XV10 / 4.G Wiring Diagrams Workshop Manual

239
B 2 BRAKE FLUID LEVEL SW1±2 : CLOSED WITH FLOAT DOWN
C 8(A), C 9(B), C10(C)
COMBINATION METER(A)2, (B)6, (B)9±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
(A)3, (B)14, (C)8±GROUND : ALWAYS CONTINUITY
F15
FUEL SENDER2±3 : APPROX. 3
WITH FUEL FULL
APPROX. 110.0
WITH FUEL EMPTY
O 1
OIL PRESSURE SW1±GROUND : CLOSED WITH OIL PRESSURE BELOW 0.2 KG/CM2 (2.84 PSI, 19.61 KPA)
P 2
PARKING BRAKE SW (1MZ±FE A/T)1±GROUND : CLOSED WITH PARKING BRAKE PEDAL DEPRESSED
P 3
PARKING BRAKE SW (EX. 1MZ±FE A/T)1±GROUND : CLOSED WITH PARKING BRAKE LEVER PULLED UP
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
B 228 (1MZ±FE), 30 (5S±FE)D 432P 233
C 8A32F1534 (S/D), 35 (C/P), 36 (W/G)P 333
C 9B32I 228 (1MZ±FE), 30 (5S±FE)V 528 (1MZ±FE), 30 (5S±FE)
C10C32J 233W 228 (1MZ±FE), 30 (5S±FE)
C1432O 128 (1MZ±FE), 30 (5S±FE)
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
125R/B NO. 1 (LEFT KICK PANEL)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1B
1C
1D20COWL WIRE AND J/B NO 1 (INSTRUMENT PANEL LEFT)1F20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
1L
1M
2G22COWL WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
3A
3B24COWL WIRE AND J/B NO 3 (BEHIND COMBINATION METER)3C24COWL WIRE AND J/B NO. 3 (BEHIND COMBINATION METER)
3D
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
II142COWL WIRE AND INSTRUMENT PANEL WIRE
IJ142FLOOR NO. 1 WIRE AND COWL WIRE
IP144ENGINE WIRE AND COWL WIREIP344ENGINE WIRE AND COWL WIRE
46 (S/D)
BX148 (C/P)FUEL GAUGE WIRE AND FLOOR NO. 1 WIREBX1
50 (W/G)
FUEL GAUGE WIRE AND FLOOR NO. 1 WIRE
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
ED38 (1MZ±FE)INTAKE MANIFOLD LHED40 (5S±FE)INTAKE MANIFOLD LH
IE42LEFT KICK PANELIF42LEFT KICK PANEL
IG42INSTRUMENT PANEL BRACE LH
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
I 644INSTRUMENT PANEL WIREI1344COWL WIRE
I 944COWL WIREI1844ENGINE WIRE
SERVICE HINTS

243
FAN MOTOR OPERATION
WITH THE IGNITION SW IS TURNED ON, CURRENT FLOWS FROM ECU±IG FUSE TO RADIATOR FAN RELAY NO. 1 (COIL SIDE) AND
RADIATOR FAN RELAY NO. 2 (COIL SIDE) " TERMINAL 2 OF THE A/C SINGLE PRESSURE SW " TERMINAL 3 " TERMINAL 2 OF THE
WATER TEMP. SW " TERMINAL 1 " GROUND, AND RADIATOR FAN RELAY NO. 1 AND NO. 2 ARE TURNED ON.
*RADIATOR FAN MOTOR OPERATION
WHEN THE IGNITION SW IS TURNED ON, RADIATOR FAN RELAY NO. 1 IS TURNED ON. IF AT THIS TIME THE ENGINE COOLANT
TEMPERATURE IS APPROX. 90°C (194°F) OR HIGHER, THE WATER TEMP. SW IS TURNED OFF, RADIATOR FAN RELAY NO. 1 IS
TURNED OFF.
AS A RESULT, CURRENT FROM THE RDI FAN FUSE TO RADIATOR FAN RELAY NO. 1 (POINT SIDE) " TERMINAL 2 OF THE
RADIATOR FAN MOTOR " TERMINAL 1 " GROUND, THUS ACTIVATING THE ROTATION OF THE RADIATOR FAN MOTOR.
*LOW SPEED OPERATION
WHEN THE IGNITION SW IS TURNED ON AND THE A/C ACTIVATED, RADIATOR FAN RELAY NO. 1 AND RADIATOR FAN RELAY NO. 2
ARE TURNED ON, CURRENT FLOWS FROM A/C MAGNETIC CLUTCH RELAY (POINT SIDE) TO RADIATOR FAN RELAY NO. 3 (COIL
SIDE) " GROUND, AND RADIATOR FAN RELAY NO. 3 IS TURNED ON.
AS A RESULT, CURRENT FLOWS FROM CDS FAN FUSE TO TERMINAL 2 OF THE A/C CONDENSER FAN MOTOR " TERMINAL 1 "
RADIAOTR FAN RELAY NO. 2 (POINT SIDE) " RADIATOR FAN RELAY NO. 3 (POINT SIDE) " TERMINAL 2 OF THE RADIATOR FAN
MOTOR " TERMINAL 1 " GROUND, FLOWING TO EACH FAN MOTOR IN SERIES, CAUSING THE FAN TO AT LOW SPEED.
*HIGH SPEED OPERATION OF THE FAN MOTOR DUARING A/C OPERATION
WHEN THE A/C OPERATION, THE REFRIGERRANT PRESSURE BECOME HIGHER THAN OR DINARY LEVEL (APPROX. 15.58 KG/CM
2
(221.2 PSI, 1527 KPA)) THE A/C SINGLE PRESSURE SW IS TURNED OFF. AS A RESULT, RADIATOR FAN RELAY NO. 1 AND RADIATOR
FAN RELAY NO. 2 ARE TURNED OFF, AND CURRENT FLOWS FROM RDI FUSE TO RADIATOR FAN RELAY NO. 1 (POINT SIDE) "
TERMINAL 2 OF THE RADIATOR FAN MOTOR " TERMINAL 1 " GROUND, AND CURRENT FLOWS FROM CDS FAN FUSE TO
TERMINAL 2 OF THE A/C CONDENSER FAN MOTOR " TERMINAL 1 " RADIATOR FAN RELAY NO. 2 (POINT SIDE) " GROUND, AND
TO EACH FAN MOTOR IN PARALLEL, THUS CAUSING THE FAN MOTORS OPERATE HIGH SPEED.
NOTE THAT, BECAUSE THE CURRENT FLOWS IN THE SAME MENNER EVEN IF THE ENGINE COOLANT TEMPERATURE IS APPROX.
90°C (194°F) OR HIGHER, THE FAN MOTOR OPERATE AT HIGH SPEED.
A 2 A/C SINGLE PRESSURE SW
2±3 : OPEN ABOVE APPROX. 15.58 KG/CM2 (221.2 PSI, 1527 KPA)
CLOSE BELOW APPROX. 15.56 KG/CM2 (178.4 PSI, 1231 KPA)
2 1
2 1 A1R1 BLACKGRAY
12E5 A2BLACK
23
SYSTEM OUTLINE
SERVICE HINTS

249
1. AIR INLET CONTROL SERVO MOTOR OPERATION (FOR PUSH SW TYPE)
(SWITCHING FROM FRESH TO RECIRC)
WITH THE IGNITION SW ON, CURRENT FROM THE GAUGE FUSE FLOWS TO TERMINAL 1 OF THE SERVO MOTOR. WHEN THE
RECIRC SW IS TURNED ON, THE CURRENT FLOWS FROM SERVO MOTOR " TERMINAL 3 " TERMINAL 5 OF THE HEATER
CONTROL SW " TERMINAL 1 " GROUND, THE MOTOR ROTATES AND THE DAMPER MOVES TO THE RECIRC SIDE. WHEN IT IS IN
THE RECIRC POSITION, THE CIRCUIT IS CUT INSIDE THE SERVO MOTOR AND THE DAMPER STOPS IN THAT POSITION.
WHEN THE CIRCUIT FOR THE INDICATOR LIGHT, CURRENT FLOWS FROM THE GAUGE FUSE " TERMINAL 12 OF THE HEATER
CONTROL SW " INDICATOR LIGHT " TERMINAL 1 " GROUND AND THE INDICATOR LIGHT CONTINUES TO LIGHT UP WHILE THE
RECIRC SW IS ON.
(SWITCHING FROM RECIRC TO FRESH)
WHEN THE IGNITION IS ON AND THE FRESH SW IS TURNED ON, CURRENT FLOWS FROM TERMINAL 2 OF THE SERVO MOTOR "
TERMINAL 6 OF THE HEATER CONTROL SW " TERMINAL 1 " GROUND, THE MOTOR ROTATES AND THE DAMPER MOVES TO THE
FRESH SIDE. WHEN THE DAMPER IS IN THE FRESH POSITION, THE CIRCUIT IS CUT INSIDE THE SERVO MOTOR AND THE DAMPER
STOPS IN THAT POSITION.
2. OPERATION OF AIR VENT MODE CONTROL SERVO MOTOR
WHEN THE IGNITION SW ON, CURRENT FLOWS FROM THE GAUGE FUSE TO TERMINAL 12 OF THE HEATER CONTROL SW,
TERMINAL 6 OF THE AIR VENT MODE CONTROL SERVO MOTOR.
WHEN THE DAMPER IS IN FACE POSITION AND THE BI±LEVEL OF THE HEATER CONTROL SW IS THEN TURNED ON, CURRENT
FLOWS FROM TERMINAL 3 OF THE HEATER CONTROL SW " TERMINAL 4 OF THE AIR VENT MODE CONTROL SERVO MOTOR SO
THAT A SINGAL THAT THE GROUND CIRCUIT IS ACTIVATED IS INPUT TO TERMINAL ªBº OF THE CONTROL CIRCUIT INSIDE THE AIR
VENT MODE CONTROL SERVO MOTOR.
SIMULTANEOUSLY, A SIGNAL THAT THE GROUND CIRCUIT IS NOT ACTIVATED IS INPUT TO TERMINAL ªAº OF THE CONTROL
CIRCUIT INSIDE THE SERVO MOTOR. THESE TWO SIGNALS ACTIVATE THE CONTROL CIRCUIT SO THAT CURRENT FROM THE
GAUGE FUSE TO THE SERVO MOTOR, CAUSING THE SERVO MOTOR TO OPERATE AND THE DAMPER TO MOVE TO BI±LEVEL
POSITION. WHEN THE DAMPER REACHES BI±LEVEL POSITION, A GROUND CUT SIGNAL IS INPUT TO TERMINAL ªBº OF THE
CONTROL CIRCUIT, THE CONTROL CIRCUIT OPERATES, THE SERVO MOTOR STOPS ROTATING AND THE DAMPER STOPS AT
BI±LEVEL.
WHEN ANOTHER MODE POSITION IS SWITCHED TO, INPUT OF SIGNALS TO TERMINAL ªAº AND TERMINAL ªBº OF THE CONTROL
CIRCUIT THAT GROUND IS MADE OR GROUND IS NOT MADE (AS EXPLAINED ABOVE) ACTIAVTES THE CONTROL CIRCUIT AND
MOVES THE SERVO MOTOR TO THE DESIRED POSITION.
3. AIR CONDITIONING OPERATION
WHEN THE IGNITION SW ON, CURRENT FLOWS FROM GAUGE FUSE TO TERMINAL 12 OF THE HEATER CONTROL SW, TERMINAL 6
OF THE AIR VENT MODE CONTROL SERVO MOTOR.
WHEN THE BLOWER SW IS ON, CURRENT FLOWS FROM THE GAUGE FUSE " HEATER RELAY (COIL SIDE) " TERMINAL 7 OF THE
BLOWER SW " TERMINAL 5 " GROUND, ACTIVATING THE HEATER RELAY. THIS CAUSES CURRENT TO FLOW FROM THE HEATER
FUSE TO THE HEATER RELAY (POINT SIDE) " A/C FUSE " TERMINAL 7 OF THE HEATER CONTROL SW (A/C SW). IF THE HEATER
CONTROL (A/C SW) IS THEN TURNED ON AT THIS TIME, A SIGNAL IS INPUT TO THE A/C AMPLIFIRE. THIS ACTIVATES THE A/C
AMPLIFIER AND A/C MAGNETIC CLUTCH RELAY SO THAT CURRENT FLOWS FROM THE GAUGE FUSE TO THE A/C MAGNETIC
CLUTCH RELAY (POINT SIDE) " A/C MAGNETIC CLUTCH, CAUSING THE COMPRESSOR TO OPERATE. THE VSV (FOR A/C IDLE±UP)
IS TURNED ON SIMULTANEOUSLY TO PREVENT A DECREASE IN ENGINE SPEED DUE TO A/C OPERATION.
HEATER RELAY
(4)5± (4)4 : CLOSED WITH THE IGNITION SW ON AND BLOWER SW ON
A/C MAGNETIC CLUTCH RELAY
(4)5± (4)3 : CLOSED WITH THE IGNITION SW ON AND BLOWER SW ON AND A/C SW ON
A 2 A/C DUAL PRESSURE SW
1±4 : OPEN WITH PRESSURE 2.1 KG/CM (30 PSI, 206 KPA) OR ABOVE 27 KG/CM (384 PSI, 2646 KPA)
B 5 BLOWER RESISTOR
6±2 : APPROX. 1.12 W
2±3 : APPROX. 0.5 W
3±1 : APPROX. 0.2 W
SYSTEM OUTLINE
SERVICE HINTS

254
AIR CONDITIONING (LEVER CONTROL SW TYPE)
CURRENT ALWAYS FLOWS FROM THE HEATER FUSE TO TERMINAL 5 OF THE HEATER RELAY. WHEN THE IGNITION SW IS TURNED
ON, CURRENT FLOWS FROM GAUGE FUSE TO TERMINAL 2 OF THE AIR VENT MODE CONTROL SERVO MOTOR AND A/C MAGNETIC
CLUTCH RELAY (COIL SIDE) " TERMINAL 12 OF THE A/C AMPLIFIER, TERMINAL 1 OF THE A/C DUAL PRESSURE SW " TERMINAL 4
" TERMINAL 2 OF THE A/C AMPLIFIER, HEATER RELAY (COIL SIDE) " TERMINAL 3 OF THE BLOWER SW.
1. OPERATION OF AIR VENT MODE CONTROL SERVO MOTOR
WHEN THE DAMPER IS IN FACE POSITION AND THE BI±LEVEL OF THE AIR VENT MODE CONTROL SW IS THEN TURNED ON,
CURRENT FLOWS FROM TERMINAL 7 OF THE AIR VENT MODE CONTROL SW " TERMINAL 5 OF THE AIR VENT MODE CONTROL
SERVO MOTOR SO THAT A SIGNAL THAT THE GROUND CIRCUIT IS ACTIVATED IS INPUT TO TERMINAL ªBº OF THE CONTROL
CIRCUIT INSIDE THE AIR VENT MODE CONTROL SERVO MOTOR. SIMULTANEOUSLY, A SIGNAL THAT THE GROUND CIRCUIT IS NOT
ACTIVATED IS INPUT TO TERMINAL ªAº OF THE CONTROL CIRCUIT INSIDE THE SERVO MOTOR. THESE TWO SIGNALS ACTIVATE
THE CONTROL CIRCUIT SO THAT CURRENT FROM THE GAUGE FUSE TO THE SERVO MOTOR, CAUSING THE SERVO MOTOR TO
OPERATE AND THE DAMPER TO MOVE TO BI±LEVEL POSITION. WHEN THE DAMPER REACHES BI±LEVEL POSITION. A GROUND
CUT SIGNAL IS INPUT TO TERMINAL ªBº OF THE CONTROL CIRCUIT, THE CONTROL CIRCUIT OPERATES, THE SERVO MOTOR
STOPS ROTATING AND THE DAMPER STOPS AT BI±LEVEL.
WHEN ANOTHER MODE POSITION IS SWITCHED TO, INPUT OF SIGNALS TO TERMINAL ªAº AND TERMINAL ªBº OF THE CONTROL
CIRCUIT THAT GROUND IS NOT MADE (AS EXPLAINED ABOVE) ACTIVATES THE CONTROL CIRCUIT AND MOVES THE SERVO
MOTOR TO THE DESIRED POSITION.
2. AIR CONDITIONING OPERATION
WHEN THE BLOWER SW IS ON, CURRENT FLOWS THE GAUGE FUSE " HEATER RELAY (COIL SIDE) " TERMINAL 3 OF THE
BLOWER SW " TERMINAL 1 " GROUND, ACTIVATING THE HEATER RELAY. THIS CAUSES CURRENT TO FLOW FROM THE HEATER
FUSE TO THE HEATER RELAY (POINT SIDE) " A/C FUSE " TERMINAL 2 OF THE A/C SW. IF THE A/C SW IS THEN TURNED ON AT
THIS TIME. A SIGNAL IS INPUT TO THE A/C AMPLIFIER. THIS ACTIVATES THE A/C AMPLIFER AND A/C MAGNETIC CLUTCH RELAY SO
THAT CURRENT FLOWS FROM THE GAUGE FUSE TO THE A/C MAGNETIC CLUTCH RELAY (POINT SIDE) " A/C MAGNETIC CLUTCH.
CAUSING THE COMPRESSOR TO OPERATE. THE VSV (FOR A/C IDLE±UP) IS TURNED ON SIMULTANEOUSLY TO PREVENT A
DECREASE IN ENGINE SPEED DUE TO A/C OPERATION.
HEATER RELAY
(4)5± (4)4 : CLOSED WITH THE IGNITION SW ON AND BLOWER SW ON
A/C MAGNETIC CLUTCH RELAY
(5)5± (5)3 : CLOSED WITH THE IGNITION SW ON AND BLOWER SW ON AND A/C SW ON
A 2 A/C DUAL PRESSURE SW
1±4 : OPEN WITH PRESSURE 2.1 KG/CM (30 PSI, 206 KPA) OR ABOVE 27 KG/CM (384 PSI, 2646 KPA)
B 5 BLOWER RESISTOR
6±1 : APPROX. 3.17 W
6±3 : APPROX. 1.38 W
2±6 : APPROX. 0.38 W
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
A 228 (1MZ±FE), 30 (5S±FE)A1732H 833
A 328 (1MZ±FE), 30 (5S±FE)B 432I 230 (5S±FE)
A1032B 532J 133
A1132B 632
A1232C1432
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
425R/B NO. 4 (RIGHT KICK PANEL)
526R/B NO. 5 (ENGINE COMPARTMENT LEFT)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1B20COWL WIRE AND J/B NO 1 (INSTRUMENT PANEL LEFT)1D20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
SYSTEM OUTLINE
SERVICE HINTS

1
234
33 CAM RY
4ACC
IG1
ST1
IG2
ST2 AM1 2
AM2
1G 91G 3
1E 11B 6
3EF1
3D 6
1C 113C 1813 B 2C 1A 2A 11 A 16 B 4B 9B 6B 4A15 B
8A 7A 6A 8C 7C 11B 5A 4C 7B 9A 3C 12B14 1C 3A 10 A 5B 8B 3B
5IJ1 11IJ1 18IJ1
1 BX1 2 BX1 3 BX1 1 6 I P3 6 I P3 8 I P1 2IP3 11IP31D 13
3D 13
3D 121D 12
3A 10
F
F
EDIE1M 1
IG 11 4II13B 33C8 2
A 1
1C 8
1M 5 123 32
1B±Y
R± L R± L
BR
R±LR± Y
R± W
R± WV± Y
W± B W±B W±BR± W R± W R± W W±B W± B W± B R± Y R± YP LG
B(
*3) Y±GBR BR Y±L Y± R Y± R
Y± L
BR
BR BR BR BR
Y±G
B G± B
BY± L Y±R BWW
BR
I12
IGNI TION SW
100A ALT
BATTERY
10A
GAUGE
2 1
F1 5
FUEL SENDER V5
VEHICLE
SPEED SENSOR
(
SPEED SENSOR)
FUEL
FUEL
WATER
TEMP.
TACHO
ABS
SEAT BELT
CRUI SE
(
*5)
OIL
BRAKE
BULB
CHE CK See ABS Sy st e m
<25±3><26±3>
See Unloc k and
Seat Belt
War ning Sy stem
< 34±2>
Se e Cr ui se
Co nt r o l Sys t em
< 24±3>
See En gi ne
Con t r o l S ys t em
<3±3><4±4><5±4>
B2
BRAKE FLUID
LEVEL SW J2
JUNCTION
CONNECTOR
P3
PARKI NG
BRAKE SWJ2
JUNCTION
CONNECTOR
REAR LIGHT FUSE BOX
From Daytime Running
Light Relay< 10±2>
From ABS ECU< 25±4>
P2
PARKING
BRAKE SW See Stop Light
System
< 8±1> < 9±1>See Char ging
System< 2±4>
See Int erior Light
Sys tem< 10±3> < 11±2>
<13±2><14±4>
To O/D Main SW
< 6±5> < 7±5>O/D OFF
CHARGE
OPEN DOOR
METER
ILLUMINATION
POWER
TURN RH
TURN LH
SRS
HIGH BEAM Se e SRS Sy st em
< 23±3>
See Headlight System
< 8±4> < 10±3> O1
OI L P RE SS U RE SW
10 B
5IP3
1Y±B Y±B
See Headlight Syst em
<8±4><10±3> Se e SRS Sy st e m
< 23±3>See Turn Signal and
Hazard Warning Light
Syst em< 9±4> < 18±4> From Elect ronic Contr olled
Transmiss ion Patt ern
Select SW<6±4><7±4> See Illumination
System< 15±2> See Inter ior Light
System< 10±3> < 11±2>
< 13±2> < 14±4> See Char ging
System< 2±4>
Fr om º STARTERº
Fuse< 1±2> < 2±2> Fr om Engine Control Module
(
Engine and Electr onic
Cont rolled Transmission ECU)
<3±6><4±6><6±3><7±2>
Fr om Engine Control Module
(
Engine ECU)
<5±4>J1
JUNCTION
CONNECTOR
FL MAIN
2. 0L
13 9 8 7 6 5 4 3 2 1101112
16 11 10 9 8 5 4 3 2 112131467 1510 9 8 7 6 5 4 3 2 1
BAC
GRAY BLUE
COMBI NATI ON METERCOMBINATION METER
B *3: 5S±FE *2 : 1MZ± FE *1 : Canada
40A
AM1
(
US A)
Intake manifold
LHLeft kick
panel
See Illumination
System< 15±2>13 A
L±R
(
*4) (
*4) (
*4)
*4 : w/o A/T Indicator
D D
G±O G± O
(
*4) (
*4)
J2
JUNCTION
CONNECTOR
C
C
12 A
GIP3 14SPEED R± L
6
1D
22
3D
10
3BR±L
V±Y
B±W
*5 : Malfunction Indicator
Lamp(
Check Engine)
(
*4)
(
*4) (
*2) BR
(
*2)
A
ABR
(
*3)
Fr om Engine Cont rol
Module(
Engine and
Electr onic Controlled
Tr ans mis sion ECU)
<3±6>From Igniter
< 2±3>
B(
*2)
Power
SourceC o mb in a tio n M e te r
W
A
A
J7
JUNCTION
CONNECTOR
1
W2
WATER TEMP. SENDER
1B 1A
1C
F10 A , F16 C,B
C9C8
C8 A ,C10 C,C9 BC10
A (
1 MZ± FE)
F10FUSE BOX
1 C F1 61
Ins trument panel
brace LHB (
5S±FE)
F10FUSE BOX (
*2)
(
*3)3D10
V±Y
Fr om Cr uise
Control ECU< 24±2>
3D 83B12
R± W
R± Y
From Cruis e Contr ol
ECU< 24±3>